Hi SpiderKenny thank you for the reply.
May you attempt to attach a RF module and share your code?
From this site rc-switch - Arduino library to operate low cost 315 MHz / 433 MHz remote control devices - Google Project Hosting
I am trying to run the examples below. The issue is with the include statements below.
Arduino.h for Galileo does not reference wiring_digital.c.
#if defined(ARDUINO) && ARDUINO >= 100
#include "Arduino.h"
#elif defined(ENERGIA) // LaunchPad, FraunchPad and StellarPad specific
#include "Energia.h"
#else
#include "WProgram.h"
#endif
The following articles look close to achieving this.
The Garage Lab :: Wireless Communications - 433MHz Modules
Welcome to pySerial’s documentation — pySerial 2.7 documentation
/*
Simple example for receiving
http://code.google.com/p/rc-switch/
Need help? http://forum.ardumote.com
*/
#include <RCSwitch.h>
RCSwitch mySwitch = RCSwitch();
void setup() {
Serial.begin(9600);
mySwitch.enableReceive(0); // Receiver on inerrupt 0 => that is pin #2
}
void loop() {
if (mySwitch.available()) {
int value = mySwitch.getReceivedValue();
if (value == 0) {
Serial.print("Unknown encoding");
} else {
Serial.print("Received ");
Serial.print( mySwitch.getReceivedValue() );
Serial.print(" / ");
Serial.print( mySwitch.getReceivedBitlength() );
Serial.print("bit ");
Serial.print("Protocol: ");
Serial.println( mySwitch.getReceivedProtocol() );
}
mySwitch.resetAvailable();
}
}
/*
RCSwitch - Arduino libary for remote control outlet switches
Copyright (c) 2011 Suat Özgür. All right reserved.
Contributors:
- Andre Koehler / info(at)tomate-online(dot)de
- Gordeev Andrey Vladimirovich / gordeev(at)openpyro(dot)com
- Skineffect / http://forum.ardumote.com/viewtopic.php?f=2&t=46
- Dominik Fischer / dom_fischer(at)web(dot)de
- Frank Oltmanns / <first name>.<last name>(at)gmail(dot)com
Project home: http://code.google.com/p/rc-switch/
This library is free software; you can redistribute it and/or
modify it under the terms of the GNU Lesser General Public
License as published by the Free Software Foundation; either
version 2.1 of the License, or (at your option) any later version.
This library is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
Lesser General Public License for more details.
You should have received a copy of the GNU Lesser General Public
License along with this library; if not, write to the Free Software
Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
#ifndef _RCSwitch_h
#define _RCSwitch_h
#if defined(ARDUINO) && ARDUINO >= 100
#include "Arduino.h"
#elif defined(ENERGIA) // LaunchPad, FraunchPad and StellarPad specific
#include "Energia.h"
#else
#include "WProgram.h"
#endif
// At least for the ATTiny X4/X5, receiving has to be disabled due to
// missing libm depencies (udivmodhi4)
#if defined( __AVR_ATtinyX5__ ) or defined ( __AVR_ATtinyX4__ )
#define RCSwitchDisableReceiving
#endif
// Number of maximum High/Low changes per packet.
// We can handle up to (unsigned long) => 32 bit * 2 H/L changes per bit + 2 for sync
#define RCSWITCH_MAX_CHANGES 67
#define PROTOCOL3_SYNC_FACTOR 71
#define PROTOCOL3_0_HIGH_CYCLES 4
#define PROTOCOL3_0_LOW_CYCLES 11
#define PROTOCOL3_1_HIGH_CYCLES 9
#define PROTOCOL3_1_LOW_CYCLES 6
class RCSwitch {
public:
RCSwitch();
void switchOn(int nGroupNumber, int nSwitchNumber);
void switchOff(int nGroupNumber, int nSwitchNumber);
void switchOn(char* sGroup, int nSwitchNumber);
void switchOff(char* sGroup, int nSwitchNumber);
void switchOn(char sFamily, int nGroup, int nDevice);
void switchOff(char sFamily, int nGroup, int nDevice);
void switchOn(char* sGroup, char* sDevice);
void switchOff(char* sGroup, char* sDevice);
void switchOn(char sGroup, int nDevice);
void switchOff(char sGroup, int nDevice);
void sendTriState(char* Code);
void send(unsigned long Code, unsigned int length);
void send(char* Code);
#if not defined( RCSwitchDisableReceiving )
void enableReceive(int interrupt);
void enableReceive();
void disableReceive();
bool available();
void resetAvailable();
unsigned long getReceivedValue();
unsigned int getReceivedBitlength();
unsigned int getReceivedDelay();
unsigned int getReceivedProtocol();
unsigned int* getReceivedRawdata();
#endif
void enableTransmit(int nTransmitterPin);
void disableTransmit();
void setPulseLength(int nPulseLength);
void setRepeatTransmit(int nRepeatTransmit);
#if not defined( RCSwitchDisableReceiving )
void setReceiveTolerance(int nPercent);
#endif
void setProtocol(int nProtocol);
void setProtocol(int nProtocol, int nPulseLength);
private:
char* getCodeWordB(int nGroupNumber, int nSwitchNumber, boolean bStatus);
char* getCodeWordA(char* sGroup, int nSwitchNumber, boolean bStatus);
char* getCodeWordA(char* sGroup, char* sDevice, boolean bStatus);
char* getCodeWordC(char sFamily, int nGroup, int nDevice, boolean bStatus);
char* getCodeWordD(char group, int nDevice, boolean bStatus);
void sendT0();
void sendT1();
void sendTF();
void send0();
void send1();
void sendSync();
void transmit(int nHighPulses, int nLowPulses);
static char* dec2binWzerofill(unsigned long dec, unsigned int length);
static char* dec2binWcharfill(unsigned long dec, unsigned int length, char fill);
#if not defined( RCSwitchDisableReceiving )
static void handleInterrupt();
static bool receiveProtocol1(unsigned int changeCount);
static bool receiveProtocol2(unsigned int changeCount);
static bool receiveProtocol3(unsigned int changeCount);
int nReceiverInterrupt;
#endif
int nTransmitterPin;
int nPulseLength;
int nRepeatTransmit;
char nProtocol;
#if not defined( RCSwitchDisableReceiving )
static int nReceiveTolerance;
static unsigned long nReceivedValue;
static unsigned int nReceivedBitlength;
static unsigned int nReceivedDelay;
static unsigned int nReceivedProtocol;
#endif
/*
* timings[0] contains sync timing, followed by a number of bits
*/
static unsigned int timings[RCSWITCH_MAX_CHANGES];
};
#endif
Attached is the sample code I am trying to run from rc-switch - Arduino library to operate low cost 315 MHz / 433 MHz remote control devices - Google Project Hosting
Any advice would be appreciated.